Alb. 28287 posts · Joined 2006. #10 · Aug 17, 2008. QUOTE (hjcrichard @ 17 Aug 2008, 09:36 PM) < {POST_SNAPBACK}> It was when the setting for the standard nuts was 130nm. The locking one was 110nm at the time. Then they changed it to 110nm for both. I think that they were all at 110 prior to that though. I've never changed mine from that figure.
On the Focus MK2/MK2.5 there is a limited range to adjust the toe on the rear axle. It can happen that the optimal toe can not be achieved because it is not possible to adjust the eccentric rear toe bolts any further. If the rear toe adjustment is completely out of specification there could be something wrong with the rear suspension or bushes. Tighten the oil filler cap. Step 23. Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine. Step 24. Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary. Replacement: engine oil and filter – FORD KUGA II (DM2). RE: 2000 ford focus zx3--negative reat tire camber causing excesstive rear tire wear. The car was lowered approx 1.8 inches prior to me buying the car. My research shows that I need to purchase adjust …

Important! Replacement: brake caliper – Ford Focus MK2. Check the brake fluid level in the reservoir and top up if necessary. Without starting the engine, press the brake pedal several times until you feel significant resistance. WELL DONE! AUTODOC recommends: Replacement: brake caliper – Ford Focus MK2. AUTODOC recommends:

Screw the front arm fastener. Use a drive socket #18. Use a torque wrench. Tighten it to 115 nm torque. 24 Tighten the rear fastener connecting the arm to the body subframe. Use a drive socket #15. Use a torque wrench. Tighten it to 120 nm torque. WWW.AUTODOC.CO.UK 14–23

Ford Focus Mk2 Lower Wishbone. By anta, January 18, 2015 in Ford Focus Club Share Car: Ford Focus Sport 1.8 TDCI 2006. Thanks, Ann. Quote; Link to comment

56 posts · Joined 2008. #5 · Apr 23, 2008. Is the ST affected by incorrect torque settings? I have a torque wrench somewhere from may days with the Lotus Elise, which apparently was sensitive to the torque settings. Can't remember what the results could be of over/under tightening them, apart from the wheel working loose if very under tight!
1209 posts · Joined 2018. #1 · Jan 9, 2020 (Edited by Moderator) Torque (lb ft) Notes Suspension. Front Suspension. steering column shaft bolt 21 front stabilizer bar link lower nuts 46 tie rod end nut 35 exhaust pipe hanger assembly bolts 18 engine roll restrictor bolt 63 front subframe bracket bolts 35 braket to front subframe bolts 46 Just use the Mk3 settings, same thing. "Flywheel bolt torque: stage 1: 22 ft-lbs. stage 2: 44 ft-lbs. final stage: additional 1/4 turn (90o turn) pressure plate bolt torque: hand tight, then tighten diagonally or in a pattern, in stages, to a final torque of 15 ft-lbs. Tightening the bolts in stages like 2 turns each bolt in a star pattern Focus 2004.75 (07.2004-) > Ford Workshop Service and Repair Manuals > Mechanical Repairs | 3 Powertrain | 303 Engine | 303-01D Engine - 2.5L Duratec-ST (VI5) | Description and Operation | General Procedures | Valve Clearance Adjustment
14 Oct 2019. #6. I’ve never torqued Ford front or rear hub nuts. I either just gun them up or use an 18” bar. Just do them tight. If your really bothered, tighten them to 210 Nm and then give them just a little bit more with a long bar.
Stage 1 - 45Nm. Stage 2 - 90 Deg. You are supposed to use a new bolt BTW. xxxwindyxxx Discussion starter. 5408 posts · Joined 2011. #5 · Jul 10, 2011. lol i was looking around net to try and find the setting and a few fourms said 320/ 340 nm and i tho that a 13 mm headed bolt they r dreaming. 62 posts · Joined 2007. #3 · Apr 13, 2015. vieplis said: Torque information from Haynes and Etis, in Nm (and from Haynes in lbf ft): Front caliper carrier bolts - 200 Nm (148 lbf ft); Front caliper slide pins - 28 Nm (21 lbf ft); Rear caliper carrier bolts - 110 Nm (81 lbf ft); Rear caliper slide pins - 35 Nm (26lbf ft). HNUoTg.
  • oo13k9g4c0.pages.dev/518
  • oo13k9g4c0.pages.dev/306
  • oo13k9g4c0.pages.dev/552
  • oo13k9g4c0.pages.dev/130
  • oo13k9g4c0.pages.dev/595
  • oo13k9g4c0.pages.dev/27
  • oo13k9g4c0.pages.dev/591
  • oo13k9g4c0.pages.dev/451

    • ford focus mk2 torque settings